Boise Water Heater Repair
A tank water heater in a metal drain pan on a concrete pad in a crawlspace, with insulated pipes overhead and a work light (illustrative photo)

Water Heater Installation in Boise, Idaho

Building, remodeling or moving a water heater? Call or text for a Boise installation price, and ask that the permit, the venting and the inspector's checklist each be named in it.

  • City of Boise code explained
  • Permit questions to ask
  • Price named before work starts

Water heater trouble?

Water heater trouble? Tell me what's going on, and I'll get right back to you.

* required

!Please enter your name.
!Please enter a 10-digit phone number.

Answered 24/7. Rather talk? Call or text (208) 248-9840.

Answered
24/7, weekends included
Code
Idaho State Plumbing Code, 2015 Uniform Plumbing Code (UPC) base
Permits
plumbing, plus mechanical for gas
Tank, installed (national)
about $1,000–$3,400

A water heater install in Boise is one part plumbing and one part paperwork. The heater must be sized, vented, drained and permitted to the City's rules, then inspected. Call or text with your project, and you'll get a call right back with a price; ask that the permit be its own line.

What kinds of installs does this cover?

Each project starts with a different question, so tell us which one is yours.

  • New home or addition: a first heater, sized to the household and the fuel on site.
  • Remodel: a heater relocated out of a closet, garage corner or basement.
  • Fuel change: electric to gas, or back, with new lines and venting.
  • Upsizing: a bigger tank, or a swap to tankless.
  • Like-for-like swap: see water heater replacement.

What code applies in Boise?

Idaho uses the Uniform Plumbing Code, not the International Plumbing Code. The Idaho State Plumbing Code is the 2017 edition, built on the 2015 UPC with Idaho amendments. The City of Boise adds its own installation guide, which spells out what an inspector looks at.

Idaho also deletes the model code's seismic-strap and scald-valve sections, so neither is a state requirement. A manufacturer's manual may still call for straps, so follow it.

What will the inspector check on a gas heater?

The City's guide is specific, and a careful install matches it line by line.

  • Gas line sizing: re-checked whenever the heater's load rises. A typical 50-gallon gas tank draws about 40,000 BTU, and a typical tankless about 180,000.
  • Shutoff and fittings: a shutoff within 6 feet, a dip leg ahead of the gas valve, and a new flex connector, never a reused one.
  • Regulator: needed when the gas arrives at 2 psi or higher.
  • Flue: single-wall joints take 3 screws and 6 inches of clearance to anything combustible.
  • Relief line: full size, pointing down within 45 degrees of vertical, and never plugged or run into the pan.

Gas piping is its own mechanical permit. An HVAC-licensed contractor may do gas piping, so more than one license can be involved on a single job.

The gas control valve and supply line on a gas water heater
The gas control valve, supply line and shutoff are the first things an inspector looks at.

What changes for an electric heater?

Electric installs trade venting questions for wiring ones. The City's guide wants the wiring run in conduit, and in a garage the lowest element must sit at least 18 inches up. Holders of a current HVAC or electrical license may make the connection, provided the disconnect is in sight and the circuit run is no longer than 50 feet.

Idaho Power customers replacing an electric resistance tank with a qualifying heat pump model may be eligible for a $300 incentive. Check the current amount before you buy. Details are on the gas and electric page.

Planning a build or remodel? Get an installation price and ask about the permit.

(208) 248-9840Talk to a plumber 24/7Text Us

Where should the heater go?

Boise's Water Heater Access Policy, in effect since 2020, is the rule that surprises people. A heater can't sit where replacing it means moving a furnace, washer, dryer or water-conditioning equipment, or demolishing permanent construction.

Practical effects:

  • Closets: a heater tucked behind a softener may need rearranging.
  • Garages: the ignition source must clear the floor by 18 inches.
  • Floors: any floor besides concrete needs a drain pan, 1 inch of clearance all round.
  • Alarms: the City guide expects a carbon-monoxide alarm outside sleeping areas wherever fuel-fired appliances or an attached garage exist.

Does altitude change a gas install?

Yes. Boise sits at roughly 2,700 feet. Bradford White builds standard gas models for sea level to 2,000 feet and tells owners above that to ask the dealer or maker about modifications. Ask which model suits Boise before you order.

How big should the new heater be?

Size follows the household. Rheem's guide pairs a 30 to 40 gallon tank with one or two people, and moves up to 50 to 55 gallons for a family of four or five. At five or more people, it points to a 75 gallon tank or tankless. A bigger tank costs more to buy and to heat, so don't oversize.

What should the written price list?

Ask for each of these by name before you agree to anything:

  • The heater, with its size, fuel and efficiency rating.
  • Permits, both plumbing and, for gas piping, mechanical.
  • Drain pan, relief line and cold-side shutoff, all part of a compliant install.
  • Expansion tank, if your supply has a check valve or pressure regulator.
  • Haul-away of any old unit.

How installation works

  1. Contact us by phone, text or form. Describe the project and the spot the heater will occupy.
  2. You'll get a call right back. Answered 24/7.
  3. Your price is set out in advance. Ask it to itemize the permit, venting and drain pan.
  4. The heater goes in and is tested before the visit ends. The City inspection follows separately.

Help covers the whole city, from the North End and Barber Valley to Collister and Hidden Springs, where the permit comes from the office that covers the address. The Boise permits guide shows how the paperwork runs.

New spot, new fuel or new build? Get the install priced before it starts.

(208) 248-9840Talk to a plumber 24/7Text Us

Questions homeowners ask

How much does water heater installation cost in Boise?

National averages put a tank installed at about $1,000 to $3,400, and a tankless at about $1,600 to $4,500. A new location, a fuel change or new venting adds to either, and the quote for your house arrives before the job starts.

Do I need a permit to install a water heater in Boise?

Yes. The City lists installing a water heater under plumbing permits, and gas piping is a separate mechanical permit. The licensed plumber doing the job normally applies online.

Where can a water heater go in a Boise house?

Where the City's Water Heater Access Policy allows: servicing or replacing it must not require moving a furnace, washer, dryer or softener, or removing permanent construction. A garage heater also needs its ignition source at least 18 inches off the floor.

Does a gas water heater need a drain pan?

The City's installation guide calls for a drain pan on any floor other than concrete, with at least 1 inch of clearance around the heater, piped to a drain or outside. Gas heaters need a metal or listed pan.

Can I install a water heater myself in Boise?

Idaho allows plumbing in a single- or duplex-family home you own, with the City permit still required. Gas piping and the electrical hookup follow separate licensing rules, so check those before you start.

Do I need an expansion tank?

The City's guide requires one when your plumbing is a closed system, meaning a check valve or pressure-reducing valve sits on the cold supply. Look near your main shutoff to see whether you have either.

Last updated:

Text Boise Water Heater Repair

Tell me what's going on with your water heater, and I'll get right back to you.

* required

!Please enter your name.
!Please enter a 10-digit phone number.

Rather talk? Call or text (208) 248-9840.